Not rated yet

Z AUTOMOTIVE TAZER MINI PROGRAMMER

  • $329.00
Free shipping

Brand: Z Automotive

Clear Engine Codes: Yes

Color: Black

Fan Adjustment: Yes

Tire Pressure Monitoring Recalibration: Yes

Tire Size: Up to 41in

Transfercase Calibration: Yes

Type: Re-Programmer

Qty:  
  • SKU
    JL-TAZER-MINI

Tazer JL Mini is to be an essential tool for owners of the 2018+ Wrangler JL and Jeep Gladiator.  All engine and transmission variations supported, including export models.

Simple, plug-in installation – simply unplug the SGW module and plug the Tazer JL Mini in its place.  Located above the OBD2 Diagnostic connector.

Features are all accessed using the dash display, using steering wheel buttons to navigate the menus.

Tazer JL Mini features can be broken into two categories;

Vehicle Settings – which are changes made to the Jeep like tire size, gear ratios,
or change settings to accommodate other upgrades or modifications. These
changes will continue to operate after the Tazer JL Mini is unplugged.

Live Functions – which are functions the Tazer JL Mini performs live, only while
plugged in.

Vehicle Settings:
– Change Tire Size
– Change Gear Ratio
– Change Transfer case LOW ratio
– Enable/Disable TPMS system
– Change TPMS pressure warning limit front/rear (25psi-85psi)
– Enable/Disable Backup camera
– Enable/Disable Cargo Camera input (8.4 Uconnect only)*
– Enable/Disable CD (wired audio) input*
– Enable/Disable TravelLink/XM traffic&weather
– Change Daytime Running Lights (DRL) region (type)
– Change DRL location
– Enable/Disable DRL Dropout function
– Enable/Disable factory fog lights
– Enable/Disable Fog Light Dropout (when Fogs shut off while High Beams are on)
– Enable/Disable Factory Halo lights (including BCM output for adding Halo’s)
– Enable/Disable One-touch lane change
– Change Headlight type (std/LED)
– Change Fog light type (std/LED)
– Change Taillight type (std/LED)
– Change Front Turn Signal type (std/LED) – supports aftermarket LED lights too
– Enable/Disable Trailer Tow setting
– Enable/Disable Aux Button settings
– Enable/Disable Blind Spot detection (if hardware added or removed)
– Enable/Disable/Change Parksense configuration
– Disable Electronic Sway Bar (if removed from vehicle)
– Disable Front Axle Disconnect module for axle swaps
– Disable Front and Rear Lockers for axle swaps
– Disable Electronic Steering Pump for hydraulic steering conversions
– Change cluster splash screen Wrangler/Sahara/Rubicon
– Change HVAC controls setting to allow use of dual zone controls on single zone Jeep (for those upgrading the 5″ radio)

-Enable HomeLink for those that add the Homelink Visor and harness

-Enable Proximity Entry for those that add the door handles and harnesses

-Enable 115v bed outlet for those that add the hardware on Gladiators

-Enable Automatic Headlamps (If hardware added)
– Enable/Disable PANIC button on remote
– One-touch return-to-stock – Quick “unmarry” function returns all vehicle settings back to
stock.

Live Functions:
– AutoStopStart disable – remembers last state of the auto stop start system and will set it for
you the next time you start the vehicle
– AutoTracKill – remembers last state of traction control system and will set it for you the next
time you start the vehicle
– Can disconnect sway bar in 2WD up to 30mph (any speed if button mapped SwayKill is used)
– Can use backup camera and added cargo/front/undercarriage camera or media player at
any speed
– TurnCAM – automatic backup camera when turn signals are used (8.4 uconnect only)
– Dark Mode- Turns off all exterior lighting and dash/radio/shifter lights while parked with
engine running.

-3rd Brake Flash – Set rate and number of flashes to pulse the 3rd brake light when brakes are applied for increased visibility
– Light Show mode – 6 preset and 3 make-your-own Light shows that flashes all the exterior
lights, perfect for car shows/first responders/off-road visibility. Control from Key Fob or
steering wheel buttons. Can be enabled for in-motion use for parades, off-road and legal
police/EMS.
– Axle Locker control (Rubicon) – Engage lockers in 2WD and 4Hi on demand.– TC Kill – Tuns off traction control, stability control and ABS.
– Hood Alarm – When the vehicle theft alarm is armed, monitors hood activity and will sound
the alarm and flash light shows if opened.
– Cooldown mode: Turn engine fans on demand when the ignition is on, engine not running
– Line Lock: Can lock front brakes for an easy burnout
– Rock Crawl: Can lock all four brakes by pressing steering wheel buttons to hold the vehicle
still, especially helpful when off-road.
– Winch Mode: Raise idle to 2000 RPM with a simple button press.
– Button Mapping: Use cruise up, down and right buttons as quick-access to some of Tazer
JL’s functions, when cruise control is off.
– Display DTC’s – Shows the diagnostic codes that’s making the check engine light come on.
– Clear CELs – Reset that pesky check engine light. Good when you have mods that set the
light and you know exactly why.
– 0 to 30 and 0 to 60 Timers – Displays 0-30 or 0-60 times on EVIC display

-Automatically blanks license plate lights when in Reverse on Gladiators, to remove glare on the backup camera at night.

-Vacuum/Boost gauge – Watch real-time Manifold Pressure, great for boosted/turbo applications
– Firmware updates – the new firmware is available periodically, always free!

To replace this text with your store's actual shipping info, go to "Catalog -> Product tabs" and edit the Shipping info page.
Customer reviews
There are no comments yet. Be the first to leave a comment
Please sign in to add review

We accept the following payment methods:

To replace this text with your store's actual info on payment methods, go to "Catalog -> Product tabs" and edit the Payment methods page.

This page is intended for your policy regarding returns and refunds.

Here you can provide information as to what products can be returned, how many days your customers have to return their purchase, whether they will receive a refund in the original form of payment, a replacement or a store credit, who pays for the shipping of the previously purchased products to the store, and so on.

To replace this text with your store's actual return policy, go to "Catalog -> Product tabs" and edit the Return Policy page.